Пример настройки моей ноды BPQ32 US1GHQ-5

; Basic Webmail configuration

;SIMPLE ; This set a whole load of paramters to reasonable defaults

LOCATOR=KN66IQ ; Set to your Grid Square to send reports to the BPQ32 Node Map system

SAVEMH=1 ; записывает в пам¤ть список, кого слышно на радио порте!

NODECALL=US1GHQ-5
BBSCALL=US1GHQ-8

;NODEALIAS=US1GHQ
; в алиас записываетс¤ не позывной, а какое-нибудь слово не более 6 букв
; обычно от названи¤ города...

NODEALIAS=NODKHE
BBSALIAS=BBSKHE

INFOMSG:
US1GHQ's LinBPQ Gateway
***

IDMSG:
US1GHQ-5 KHERSON BBS US1GHQ-8
***

CTEXT:
Welcome to US1GHQ BBS
Type ? for list of available commands.
***
FULL_CTEXT=1        ; 0=send CTEXT to L2 connects to NODEALIAS only ; 1=send CTEXT to all connectees

;For EasyTERM
AGWPORT=9001
AGWMASK=0x30
AGWSESSIONS=10

;Misc Settings

AUTOSAVE=1
BBS=1
NODE=1
HIDENODES=1         ; If set to 1, nodes beginning with a # ; require a 'N *' command to be displayed.
ENABLE_LINKED=N     ; Controls processing of *** LINKED command
                    ; Y = allows unrestricted use
                    ; A = allows use by application program
                    ; N = disabled

;-----------------------------------------------  NETWORK SYSTEM PARAMETERS ----------------------------------------
OBSINIT=6           ; Initial obsolescence set when a node is included ; in a received nodes broadcast. This value is then ; decremented by 1 every NODESINTERVAL.
OBSMIN=4            ; When the obsolescence of a node falls below this ; value that node`s information is not included in ; a subsequent nodes broadcast.
L3TIMETOLIVE=25     ; Max L3 hops
L4RETRIES=3         ; Level 4 retry count
L4TIMEOUT=60        ; Level 4 timeout in seconds s/b > FRACK x RETRIES
L4DELAY=2           ; Level 4 delayed ack timer in seconds
L4WINDOW=4          ; Level 4 window size
BUFFERS=4096        ; Buffer Size
NODESINTERVAL=25    ; Nodes broadcast interval in minutes
IDINTERVAL=0        ; 'IDMSG' UI broadcast interval in minutes, 0=OFF
BTINTERVAL=0        ; The BTEXT broadcast interval in minutes, 0=OFF
MAXLINKS=126        ; Max level 2 links
MAXNODES=1024       ; Max nodes in nodes table
MAXROUTES=128       ; Max adjacent nodes
MAXCIRCUITS=128     ; Max L4 circuits
MINQUAL=83          ; Minimum quality to add to nodes table
PACLEN=236          ; Max packet size (236 max for net/rom)
T3=180              ; Link validation timer in seconds
IDLETIME=900        ; Idle link shutdown timer in seconds

APRSDIGI            ; Включаем режим DIGI/IGATE
APRSCall US1GHQ-1
StatusMsg=VHF/UHF DIGI Kherson/Ingenerne
Symbol=#        ; Icon to display for station. Default is House if omitted
Symset=/
;
;    Specify a Dest and Path for each port you want to use for APRS. No dest means receive only port
;	  Ports without an APRSPath statement will not be used by the Digi
;
APRSPath 2=APRS,WIDE2-1
APRSPath 3=APRS,WIDE1-1
APRSPath 6=APRS,WIDE1-1

BeaconInterval=10      ; Send Beacon every 30 minute
DISTKM=1
MAXAGE=1440

;    Define Crossport Digi. For each port, a list of ports to send a packet to (IS means send to APRS-IS)
;    If a Digimap isn`t specified for a port, digi out on the port the packet arrived on,
;	  	  and send to APRS-IS (if enabled)
;    If you want to digi on same port, but not send to APRS-IS, Specify Digimap n=n 
;Digimap 5=5,16,       ; Packets from 5 to 16, but not APRS-IS
Digimap 2=2,IS,        ; Packets from 2 to 2 and NO APRS-IS
Digimap 3=3,IS,
Digimap 6=6,IS,

TraceCalls=WIDE,TRACE  ; Calls for CALLN-n Processing with Trace
;TraceCalls=WIDE,IN    ; Calls for CALLN-n Processing with Trace
FloodCalls=LYA         ; Calls for CALLN-n Processing without Trace
DigiCalls=US1GHQ       ; Calls for Normal (ie no SSID manipulation) Digi
                       ; For a Local "Fillin" Digi, you could include WIDE1-1 and leave out TraceCalls and FloodCalls
ReplaceDigiCalls       ; Replace DigiCalls with APRSCall. Omit if you want the call to be left as it is received.
MaxTraceHops=2         ; Max value of n in CALLN-n processing. If a packet is received with n greater than
MaxFloodHops=2         ; this, the value will be replaced BEFORE it is decremented.

; You can specify a fixed LAT/LONG instead of using GPS

LAT=4642.47N           ; Must be in standard APRS Format
LON=03240.95E          ; Must be in standard APRS Format

;IGATE Params. If specified you will gate RF packets and your beacons to APRS-IS

ISHost=aprs.mis.ks.ua     ; APRS-IS Host Name
ISPort=14580              ; Normal port for a filtered feed
ISPasscode=24487          ; If you don`t already have a passcode I can issue you one.
ISFilter=m/100            ; Filter Command if needed

***

PORT
 ID=Telnet Server
 PORTNUM=1
 DRIVER=TELNET
 CONFIG
 LOGGING=1
 DisconnectOnClose=1
 CMS=1 ; Enable CMS Gateway
 CMDPORT=63000
 HTTPPORT=9080 ; Port used for Web Management/WebMail
 TCPPORT=9010 ; Port for Telnet Access
 FBBPORT=9012 ; Not required, but allows monitoring using BPQTermTCP
 LOGINPROMPT=Callsign :
 PASSWORDPROMPT=Password :
 MAXSESSIONS=32
 USER=user,password,US1GHQ,"",SYSOP
 USER=guest,guest,GUEST,"",USER
ENDPORT

PORT
 ID=VHF_144.8MHz_1200bod
 PORTNUM=2
 TYPE=EXTERNAL
 DRIVER=BPQtoAGW
 IOADDR=1F40
 CHANNEL=A
 DIGIFLAG=1
 DIGIPORT=0
 MAXSESSIONS=10
 KISSOPTIONS=NOPARAMS
 FRACK=10000
 RESPTIME=3000
 RETRIES=5
 MAXFRAME=3
 PACLEN=256
 TXDELAY=400
 SLOTTIME=100
 PERSIST=64

 WL2KREPORT PUBLIC,www.winlink.org,8778,US1GHQ-11,KN66IQ,00-23,144800000,PKT1200,25,0
ENDPORT

PORT
 ID=VHF_432.5MHz_1200bod
 PORTNUM=3
 TYPE=EXTERNAL
 DRIVER=BPQtoAGW
; IOADDR=1F40
 CHANNEL=A
 DIGIFLAG=1
 DIGIPORT=0
 MAXSESSIONS=10
 KISSOPTIONS=NOPARAMS
 FRACK=10000
 RESPTIME=3000
 RETRIES=5
 MAXFRAME=3
 PACLEN=256
 TXDELAY=400
 SLOTTIME=100
 PERSIST=64
 WL2KREPORT PUBLIC,www.winlink.org,8778,US1GHQ-11,KN66IQ,00-23,432500000,PKT1200,5,0

 CONFIG
 172.16.10.9 8000
ENDPORT

PORT
  ID=UHF_433.775MHz_LoRa_APRS
  PORTNUM=4
  TYPE=ASYNC
  PROTOCOL=KISS
  IPADDR=172.16.10.204    ; Address of PC runnning the TNC. Usually this is the same machine as BPQ, so use 127.0.0.1 but can be on another machine
  TCPPORT=8001            ; Port TNC listens on. Default for UZ7HO is 8100 and Direwolf 8001
  CHANNEL=A
; DIGIFLAG=0
; DIGIPORT=0
  FRACK=5000
  RESPTIME=1000
  RETRIES=5
  MAXFRAME=1
  PACLEN=200
  TXDELAY=400
  SLOTTIME=100
  PERSIST=64
  ;KISSOPTIONS=NOPARAMS
ENDPORT

PORT
 ID=AXIP
 PORTNUM=5
 DRIVER=BPQAXIP
 QUALITY=192
; QUALITY лучше ставить всем 192, така¤ есть договоренность дл¤ AXUDP 
 MAXFRAME=4
 FRACK=7000
 RESPTIME=1000
 RETRIES=10
 PACLEN=236
 CONFIG
 UDP 10093        ;Listens for UDP packets on this UDP port number
 UDP 10092
 MHEARD
  
MAP K0ZCO-1 K0ZCO.DDNS.NET UDP 10093 B
MAP W5KAV-1 W5KAV.DDNS.NET UDP 10093 B
MAP KC9VYU-7 kc9vyu.4920north.com UDP 10093 B
MAP KE0GB-7 KE0GB.DDNS.NET UDP 10093 B
MAP UT1HZM-5 188.239.121.14 UDP 10093 B
MAP N3LAC-2 kc3kwa.ddns.net UDP 10093 B
MAP PE1RRR-7 static.ehvairport.com UDP 10093 B
MAP PE1RRR-5 rrrnet.ehvairport.com UDP 10093 B
MAP VK7HDM-14 203.38.121.134 UDP 10093 B
MAP EC5W-1 bpq.ec5w.es UDP 10096 B
MAP PY2BIL-4 pktsp.dynu.com UDP 10093 B
MAP VE3CGR-7 ve3cgr.dyndns.org UDP 10093 B
MAP IR2UFV-15 gw.iw2ohx.net UDP 10093 B
MAP N3HYM-5 N3HYM.DDNS.NET UDP 10093 B
MAP US1GHQ-2 172.16.21.10 UDP 10093 B
; MAP US1GBF-5 194.1.193.70 UDP 10093 B

BROADCAST NODES
AUTOADDMAP
ENDPORT

PORT
 ID=KISS_SERVER
 PORTNUM=6
 TYPE=ASYNC
 PROTOCOL=KISS
 IPADDR=0.0.0.0
 TCPPORT=9000
 DIGIFLAG=1
 DIGIPORT=0
ENDPORT

; здесь подправил ¤рлыки аппликаций, цифра после позывного (SSID) должна быть разной 

APPLICATION 1,BBS,,US1GHQ-8
APPLICATION 2,CHAT,,US1GHQ-4,KHECHT,255
APPLICATION 3,RMS,C 1 CMS HOST 0,US1GHQ-11,KHERMS,255

LINMAIL	 		; Enable BBS
LINCHAT			: Enable chat